5,838
edits
Cumulus.ini (preserving history): Difference between revisions
From Cumulus Wiki
Jump to navigationJump to search
Cumulus.ini (preserving history) (view source)
Revision as of 06:27, 17 May 2021
, 06:27, 17 May 2021→Instromet Settings
m (→WM918/WMR928 Settings: typo) |
|||
| Line 329: | Line 329: | ||
|- | |- | ||
!style="width:30px" | Parameter Line Entry | !style="width:30px" | Parameter Line Entry | ||
!style="width: | !style="width:100px" | Label on Settings page | ||
!style="width:20px" | Default | !style="width:20px" | Default | ||
!style="width:300px" | Description | !style="width:300px" | Description | ||
|- | |- | ||
|style="background:lightgray;"|[Station] | |style="background:lightgray;"|[Station] | ||
| | |||
| | |||
|style="background:lightgray;"|Section name - the following parameters relate to the station configuration. | |style="background:lightgray;"|Section name - the following parameters relate to the station configuration. | ||
|- | |- | ||
|ImetWaitTime=200 | |ImetWaitTime=200 | ||
| | |||
|200 | |||
|This parameter (attribute=value) if you need to change it from its '''default of 200 ms''' is added directly to the file, it does not appear on a configuration screen. | |This parameter (attribute=value) if you need to change it from its '''default of 200 ms''' is added directly to the file, it does not appear on a configuration screen. | ||
Specifies the time in milliseconds that Cumulus allows for a response from an Instromet station. If you are having problems with reading from an Instromet station, try inserting this line into the ''Station'' section using a value of 500. According to the specification, 500 ms is the absolute maximum time that the station should take to respond to any command. | Specifies the time in milliseconds that Cumulus allows for a response from an Instromet station. If you are having problems with reading from an Instromet station, try inserting this line into the ''Station'' section using a value of 500. According to the specification, 500 ms is the absolute maximum time that the station should take to respond to any command. | ||
|- | |- | ||
|ImetBaudRate=19200 | |ImetBaudRate=19200 | ||
| | | | ||
| 19200 | |||
| Some ?older? Instromet loggers operate at 115200, if you have one of these older loggers you will need to reset this value | |||
|- | |- | ||
|SyncDavisClock=0 | |SyncDavisClock=0 | ||
| | |||
|0 | |||
|Note despite the name of the parameter within 'Cumulus.ini', this does apply to Instromet stations. | |Note despite the name of the parameter within 'Cumulus.ini', this does apply to Instromet stations. | ||
When set, at Cumulus start-up and at 04:00 each day, Cumulus will set the Instromet clock to within a minute of the same time as the PC | When set, at Cumulus start-up and at 04:00 each day, Cumulus will set the Instromet clock to within a minute of the same time as the PC | ||
| Line 350: | Line 358: | ||
|- | |- | ||
|LogExtraSensors=0 | |LogExtraSensors=0 | ||
| | |||
|0 (disable) | |||
|If you have 'extra sensors' selected, the wet bulb reading will be used as an extra temperature sensor. Otherwise it is used as 'wet bulb' and the humidity will be calculated from that and the dry bulb sensor. | |If you have 'extra sensors' selected, the wet bulb reading will be used as an extra temperature sensor. Otherwise it is used as 'wet bulb' and the humidity will be calculated from that and the dry bulb sensor. | ||
*0=Disabled (default). For a wet bulb sensor, Cumulus will output the humidity, not the temperature shown by the wet bulb. | *0=Disabled (default). For a wet bulb sensor, Cumulus will output the humidity, not the temperature shown by the wet bulb. | ||
