5,838
edits
Cumulus.ini (preserving history): Difference between revisions
Cumulus.ini (preserving history) (view source)
Revision as of 11:58, 3 January 2013
, 11:58, 3 January 2013→Section: Station: Chill hours
m (→Section: Station: Chill hours) |
|||
| Line 67: | Line 67: | ||
*0 = Disabled | *0 = Disabled | ||
*1 = Enabled, Cumulus will calculate the dew point instead of using the value supplied by the station. This avoids the restriction in the Oregon Scientific stations where the dew point can never be below freezing point. | *1 = Enabled, Cumulus will calculate the dew point instead of using the value supplied by the station. This avoids the restriction in the Oregon Scientific stations where the dew point can never be below freezing point. | ||
|- | |- | ||
|CalculatedWC=0 | |CalculatedWC=0 | ||
| Line 73: | Line 72: | ||
*0 = Disabled | *0 = Disabled | ||
*1 = Enabled, Cumulus will calculate the wind chill instead of using the value supplied by the station. Note that some stations (Fine Offset, for example, do not supply a wind chill value anyway, so Cumulus always calculates it). You should set this if you have specified any calibration values for wind or temperature, so that Cumulus can also apply those values to the wind chill. | *1 = Enabled, Cumulus will calculate the wind chill instead of using the value supplied by the station. Note that some stations (Fine Offset, for example, do not supply a wind chill value anyway, so Cumulus always calculates it). You should set this if you have specified any calibration values for wind or temperature, so that Cumulus can also apply those values to the wind chill. | ||
|- | |||
|UseWindChillCutOff=1 | |||
|Calculate [[Wind chill]] only if temperature less than 10°C rule. | |||
*0 = Disabled (default) | |||
*1 = Enabled, this line needs to be added in the [Station] section of the Cumulus.ini | |||
Note that you need to set Cumulus to calculate the wind chill (if your station is a type that supplies one itself) for this setting to have any effect. | |||
|- | |||
|ChillHourSeasonStart=10 | |||
|The season start figure is the calendar month number (1 to 12) | |||
|- | |||
|ChillHourThreshold=45 | |||
|The temperature threshold is specified in the units that you use in Cumulus (see [[Heat/cold_degree_days_and_Chill_hours]] | |||
|- | |- | ||
|RolloverHour=0 | |RolloverHour=0 | ||
| Line 83: | Line 94: | ||
*0 = Use 10am in summer not checked on Station Configuration Screen | *0 = Use 10am in summer not checked on Station Configuration Screen | ||
*1 = Use 10am in summer selected on Station Configuration Screen | *1 = Use 10am in summer selected on Station Configuration Screen | ||
|- | |||
| | |||
SnowDepthHour=9 | |||
|Snow lying/falling roll over time (time when yesterday's values in log.xml are forgotten) | |||
*0 = midnight | |||
*9 = 9am | |||
|- | |- | ||
|ConfirmClose=0 | |ConfirmClose=0 | ||
| Line 231: | Line 248: | ||
|EWpressureoffset=x.y | |EWpressureoffset=x.y | ||
|Got a pressure problem with a Fine Offset station? This can occur on startup when the pressure 'offset' that Cumulus reads is garbage, so Cumulus just uses zero (so effectively you end up with your absolute pressure being recorded instead of relative pressure). There's a work around for this by telling Cumulus what offset to use, rather than reading it from the station. You specify it in cumulus.ini by adding a line to the [Station] section: where x.y is the difference between your station (absolute) and sea-level (relative) pressures, in mb/hPA. | |Got a pressure problem with a Fine Offset station? This can occur on startup when the pressure 'offset' that Cumulus reads is garbage, so Cumulus just uses zero (so effectively you end up with your absolute pressure being recorded instead of relative pressure). There's a work around for this by telling Cumulus what offset to use, rather than reading it from the station. You specify it in cumulus.ini by adding a line to the [Station] section: where x.y is the difference between your station (absolute) and sea-level (relative) pressures, in mb/hPA. | ||
|- | |- | ||
|Logging=1 | |Logging=1 | ||