|
|
| Line 445: |
Line 445: |
| <big>THE FOLLOWING SUB-SECTIONS NEEDS TO BE REWRITTEN - MX has changed, and the sub-sections below reflect older releases where some parameters were read-only (not set with admin interface) and some were read-write (set within admin interface)</big> | | <big>THE FOLLOWING SUB-SECTIONS NEEDS TO BE REWRITTEN - MX has changed, and the sub-sections below reflect older releases where some parameters were read-only (not set with admin interface) and some were read-write (set within admin interface)</big> |
|
| |
|
| The following list of options and allowed values is taken from '''StationOptions.json''' for release 3.10., certain settings determine which other settings are shown: | | The difficulty is ensuring this Wiki page continues to help people whichever MX release they are using - the alternative is to split this page and have references to other pages (one for early MX releases, one for 3.10.1 onwards) |
| <pre> Select Station : "Davis Vantage Pro", "Davis Vantage Pro2/Vue", "Davis WeatherLink Live",
| |
| "Oregon Scientific WMR-928", "Oregon Scientific WM-918", "Oregon Scientific WMR100", "Oregon Scientific WMR200",
| |
| "EasyWeather",
| |
| "Fine Offset", "Fine Offset with Solar Sensors",
| |
| "Instromet",
| |
| "Ecowitt GW1000",
| |
| "LaCrosse WS2300"
| |
| "loginterval": "1 minute", "5 minutes", "10 minutes", "15 minutes", "20 minutes", "30 minutes"
| |
| "logrollover": "9am", "Use 10am in Summer"
| |
| "units": "wind": "Metres per second (m/s)", "Miles per hour (mph)", "Kilometres per hour (km/h)", "Knots (kts)"
| |
| "pressure": "Milli-bar (mbar)", "Hectopascal (hPa)", "Inches of mercury (inHg)"
| |
| "temp": "Celsius", "Fahrenheit"
| |
| "rain": "Millimetres", "Inches"
| |
| "advanced": "Here be dragons! Only alter these settings if you understand what they do.",
| |
| "tempdp","pressdp","raindp","winddp", "windavgdp", "windrundp", "airqulaitydp", "sunshinedp", "uvdp"
| |
| "Location": "A short name for the location", "A longer description of the location", "Latitude", "Longitude"
| |
| "advanced": "Here be dragons! Only alter these settings if you understand what they do.",
| |
| "Records Began Date"
| |
| | |
| WEATHER STATION DEPENDENT
| |
| "davisvp2": "Serial", "TCP/IP", "Your station serial port (real or virtual)","Period to disconnect once a minute from IP loggers to allow them to upload to WeatherLink.com. Time in seconds"
| |
| "advanced": "Here be dragons! Only alter these settings if you understand what they do.",
| |
| "Synchronise station clock","Read Davis reception stats", "Set the Davis Logger interval to match Cumulus MX interval", "Enable use of the LOOP2 data packets (UseDavisLoop2)", "Davis VP 1-minute barometer update (ForceVPBarUpdate)","Time to wait after establishing a connection to an IP logger before sending commands","TCP/IP port for your logger. Default is 22222", "Serial port speed in bps",
| |
| "daviswll": "Auto-Discovery","api", "Select the ISS transmitter ID for your Wind sensor", "Select the ISS transmitter ID for your Temperature/Humidity sensor", "Select the ISS transmitter ID for your Rain sensor", Select the ISS transmitter ID for your Solar sensor", Select the ISS transmitter ID for your UV sensor", "select the transmitter ID for your extra temperature sensor #1, #2, #3, #4", "Select the transmitter ID for your extra soil moisture sensor #1, #2, #3, #4", "Select the index within the transmitter ID for your soil moisture leaf sensor #1, #2, #3, #4", Select the transmitter ID for your extra leaf sensor #1,#2", "Select the transmitter ID for your extra temperature/humidity sensor #1, #2, #3, #4, #5, #6, #7, #8", "Is sensor #1 a combined temperature/humidity sensor?"
| |
| "advanced": "Here be dragons! Only alter these settings if you understand what they do.",
| |
| "raingaugetype": "Auto", "Metric (0.2 mm)*", "Imperial (0.01 in)*", "Metric (0.1 mm)", "Imperial (0.001 in)"
| |
| "The UDP multicast port used by the WLL, this will normally be discovered from the WLL"
| |
| "gw1000": "Auto-Discovery", "ipv4", "macaddress"
| |
| "fineoffset": "Synchronise Reads",
| |
| "advanced": "Here be dragons! Only alter these settings if you understand what they do.",
| |
| "readtime", "vid", "pid"
| |
| "easyw": "How often to read the EasyWeather data file in minutes", "filename" "minpressmb", "maxpressmb", "raintipdiff", "pressoffset"
| |
| "imet": "comportname", "baudrate"
| |
| "advanced": "Here be dragons! Only alter these settings if you understand what they do.",
| |
| "syncstationclock", "syncclockhour", "updatepointer","waittime", "readdelay"
| |
| "wmr928": "comportname"
| |
| "LaCrosse": "Use computer clock instead of LaCrosse station clock for archive data"
| |
| | |
| "Options": "Use bearing zero when calm"", "Calculate average wind speed", "Use speed for average calculation", "Use 100% for 98% humidity", "Calculate dew point", "Cumulus pressure trend names", "Round wind speeds to the nearest whole number", "Display and log extra sensors, if fitted", "Make Cumulus MX run even if you do not have the minimum sensors required (temp, press, wind)"
| |
| "advanced": "Here be dragons! Only alter these settings if you understand what they do.",
| |
| "Period of time in minutes to average out wind bearings", "Period of time in minutes to average out wind speeds", "Period of time in minutes to record the peak gust speed"
| |
| "Forecast": "Use the Zambretti forecast generated by Cumulus", "If using the Cumulus forecast, update only once an hour rather than every data update", "The low pressure extreme for your location", "The high pressure extreme for your location", "The units that you have used for the pressure extremes"
| |
| "Solar": "Select the algorithm to use for solar irradiation calculations", "The percentage of the current theoretical solar value above which the sun should be considered to be shining (default = 75)", "The minimum solar reading for the sun to be considered to be shining (default = 0)", "The R-S transmission factor of the solar radiation through the atmosphere (0.70 - 0.91, default 0.80)", "The Bras turbidity factor (1.00=clear, 5.00=smoggy, default = 2.00)"
| |
| "AnnualRainfall": "Enter a rainfall amount to be added to the total for the year when you started using Cumulus - for the period for which you have no Cumulus data", "Enter the year to apply the correct to (normally this year or last year) as a four digit number. Leave as zero to disable", "Select the month from which the annual total is to be calculated",
| |
| "Graphs": "The number of hours shown on the minute-by-minute graphs", "The number of days shown on the daily graphs"; SHOW/HIDE: "Outdoor Temperature", "Indoor Temperature", "Heat Index", "Dew Point", "Wind Chill", "Apparent Temperature" , "Feels Like", "Humidex", "Daily Maximum Temperature", "Daily Average Temperature", "Daily Minimum Temperature", "Outdoor Humidity", "Indoor Humidity", "UV Index", "Solar Irradiation", "Sunshine Hours"
| |
| "DisplayOptions": "Enabling this option will display Apparent temperature on the default web site/Disabling this option will display Feels Like temperature on the default web site", "Display Solar data", "Display UV-I data", "The number of cardinal points to display on the Wind Rose",
| |
| </pre>
| |
|
| |
|
| === Spike Removal === | | === Spike Removal === |