5,838
edits
Cumulus.ini (preserving history): Difference between revisions
Cumulus.ini (preserving history) (view source)
Revision as of 17:03, 25 September 2017
, 17:03, 25 September 2017→Section: Station
m (→Davis family specific:: PORT parameter) |
|||
| Line 162: | Line 162: | ||
|- | |- | ||
|UseWindChillCutOff=1 | |UseWindChillCutOff=1 | ||
|This parameter (attribute=value) is added directly to the file, it does not appear on a configuration screen. Purpose is to disable 'calculate [[Wind chill]] only if temperature less than 10°C rule'. | |This parameter (attribute=value) is added directly to the file, it does not appear on a configuration screen. If the parameter is not included in the file, the default value is assumed. Purpose is to disable 'calculate [[Wind chill]] only if temperature less than 10°C rule'. | ||
*0 = Disabled, Cumulus will use any wind speed of 3 mph or more, to modify the temperature, and determine the wind chill ignoring the temperature criterion | *0 = Disabled, Cumulus will use any wind speed of 3 mph or more, to modify the temperature, and determine the wind chill ignoring the temperature criterion | ||
*1 = Enabled (default), Cumulus will use both 10°C temperature and 3 mph wind speed criterions to determine if wind chill applies. | *1 = Enabled (default), Cumulus will use both 10°C temperature and 3 mph wind speed criterions to determine if wind chill applies. | ||
| Line 168: | Line 168: | ||
|- | |- | ||
|ChillHourThreshold=45 | |ChillHourThreshold=45 | ||
|This parameter (attribute=value) is added directly to the file, it does not appear on a configuration screen. The temperature threshold is specified in the units that you use in Cumulus (see [[Heat/cold_degree_days_and_Chill_hours]]). The default is 45 degrees Fahrenheit (or | |This parameter (attribute=value) is added directly to the file, it does not appear on a configuration screen. The temperature threshold is specified in the units that you use in Cumulus (see [[Heat/cold_degree_days_and_Chill_hours]]). The default is exactly 45 degrees Fahrenheit (or exactly 7 degrees Celsius depending on which units you use) if the parameter has not been included. | ||
|- | |- | ||
|ChillHourSeasonStart=10 | |ChillHourSeasonStart=10 | ||
| Line 184: | Line 184: | ||
|- | |- | ||
|SnowDepthHour=9 | |SnowDepthHour=9 | ||
|This parameter (attribute=value) is added directly to the file, it does not appear on a configuration screen. This line needs to be added in the [Station] section of the Cumulus.ini, it is the [[Weather_Diary|Snow lying/falling]] roll over time (time when yesterday's values in log.xml are forgotten) - Allowed values are 0 to 23 and represent the time to the nearest hour that snow depth measurements are taken. | |This parameter (attribute=value) is added directly to the file, it does not appear on a configuration screen. If the parameter is not included in the file, the default value is assumed. This line needs to be added in the [Station] section of the Cumulus.ini, it is the [[Weather_Diary|Snow lying/falling]] roll over time (time when yesterday's values in log.xml are forgotten) - Allowed values are 0 to 23 and represent the time to the nearest hour that snow depth measurements are taken. | ||
*0 = midnight (default) | *0 = midnight (default) | ||
*9 = 9am, | *9 = 9am, | ||
| Line 263: | Line 263: | ||
|- | |- | ||
|CreateWxnowTxt=0 | |CreateWxnowTxt=0 | ||
|This parameter (attribute=value) is added directly to the file in the [station] section, it does not appear on a configuration screen. | |This parameter (attribute=value) is added directly to the file in the [station] section, it does not appear on a configuration screen. If the parameter is not included in the file, the default value is assumed. | ||
*0= turn off creation of wxnow.txt file (stored in main Cumulus folder) | *0= turn off creation of wxnow.txt file (stored in main Cumulus folder) | ||
*1= (default) create wxnow.txt file (an alternative way to get data to CWOP/APRS) | *1= (default) create wxnow.txt file (an alternative way to get data to CWOP/APRS) | ||
|- | |- | ||
|ListWebTags=0 | |ListWebTags=0 | ||
|This parameter (attribute=value) is added directly to the file in the [station] section, it does not appear on a configuration screen. | |This parameter (attribute=value) is added directly to the file in the [station] section, it does not appear on a configuration screen. If the parameter is not included in the file, the default value is assumed. | ||
*0= (default) turn off creation of WebTags.txt file (stored in main Cumulus folder) | *0= (default) turn off creation of WebTags.txt file (stored in main Cumulus folder) | ||
*1= create WebTags.txt file when Cumulus is restarted (contains an unordered list of all the web tags Cumulus can recognise) | *1= create WebTags.txt file when Cumulus is restarted (contains an unordered list of all the web tags Cumulus can recognise) | ||
| Line 286: | Line 286: | ||
|- | |- | ||
|RainDayThreshold=-1 | |RainDayThreshold=-1 | ||
|This parameter (attribute=value) is added directly to the file, it does not appear on a configuration screen. The threshold value which the daily rainfall has to equal or exceed for the day to be considered a 'rain day'. Default -1 = 0.2mm or 0.01in. Value is entered in your current [[Rain_measurement]] units. | |This parameter (attribute=value) is added directly to the file, it does not appear on a configuration screen. If the parameter is not included in the file, the default value is assumed. The threshold value which the daily rainfall has to equal or exceed for the day to be considered a 'rain day'. Default -1 = 0.2mm or 0.01in. Value is entered in your current [[Rain_measurement]] units. | ||
|- | |- | ||
|NoFlashWetDryDayRecords=1 | |NoFlashWetDryDayRecords=1 | ||
| Line 307: | Line 307: | ||
|- | |- | ||
|FCPressureThreshold=0.1 | |FCPressureThreshold=0.1 | ||
|This parameter (attribute=value) is added directly to the file, it does not appear on a configuration screen. It specifies the threshold (in mb per hour averaged over 3-hour period) for a pressure change to count as rising or falling rather than steady when determining the Zambretti forecast. The default is 0.1 mb/hr averaged over the previous three hours. | |This parameter (attribute=value) is added directly to the file, it does not appear on a configuration screen. It specifies the threshold (in mb per hour averaged over 3-hour period) for a pressure change to count as rising or falling rather than steady when determining the Zambretti forecast. The default is 0.1 mb/hr averaged over the previous three hours. If the parameter is not included in the file, the default value is assumed. | ||
|- | |- | ||
|FCpressinMB=1 | |FCpressinMB=1 | ||
| Line 326: | Line 326: | ||
|- | |- | ||
|RTdisconnectcount=N | |RTdisconnectcount=N | ||
|This parameter (attribute=value) is added directly to the file, it does not appear on a configuration screen. By default, the 'realtime' ftp connection stays connected. You can make it disconnect periodically by adding an Option to periodically disconnect the realtime FTP connection, the theory being that it will not get stuck if the server dies, and will keep trying to reconnect. | |This parameter (attribute=value) is added directly to the file, it does not appear on a configuration screen. By default, the 'realtime' ftp connection stays connected. If the parameter is not included in the file, the default value is assumed. You can make it disconnect periodically by adding an Option to periodically disconnect the realtime FTP connection, the theory being that it will not get stuck if the server dies, and will keep trying to reconnect. | ||
N must be a positive integer. For example set N to '60'; it represents the number of realtime ftp uploads between disconnections - so 60 would give an hour if 1 minute realtime interval selected. | N must be a positive integer. For example set N to '60'; it represents the number of realtime ftp uploads between disconnections - so 60 would give an hour if 1 minute realtime interval selected. | ||
|- | |- | ||
| Line 333: | Line 333: | ||
|- | |- | ||
|SpecialLog=1 | |SpecialLog=1 | ||
|This optional parameter (attribute=value) is added directly to the file, it does not appear on a configuration screen. Add this entry to start updating a file called 'speciallog.txt' in the data folder with the following fields: | |This optional parameter (attribute=value) is added directly to the file, it does not appear on a configuration screen. If the parameter is not included in the file, the default of no special log is assumed. Add this entry to start updating a file called 'speciallog.txt' in the data folder with the following fields: | ||
date(dd/mm/yy),time(hh:mm),inside temp,inside humidity,inside dewpoint,outside temp,outside humidity,outside dewpoint | date(dd/mm/yy),time(hh:mm),inside temp,inside humidity,inside dewpoint,outside temp,outside humidity,outside dewpoint | ||
| Line 349: | Line 349: | ||
|- | |- | ||
|NoSensorCheck=1 | |NoSensorCheck=1 | ||
|This parameter (attribute=value) is added directly to the file, it does not appear on a configuration screen. | |This parameter (attribute=value) is added directly to the file, it does not appear on a configuration screen. If the parameter is not included in the file, the default value is assumed. | ||
The option (for 'incomplete' stations) to disable the sensor check described in this [http://wiki.sandaysoft.com/a/FAQ#Cumulus_isn.27t_performing_periodic_tasks.2C_like_data_logging_or_web_uploads FAQ] | The option (for 'incomplete' stations) to disable the sensor check described in this [http://wiki.sandaysoft.com/a/FAQ#Cumulus_isn.27t_performing_periodic_tasks.2C_like_data_logging_or_web_uploads FAQ] | ||
*0 = Sensor check enabled (default) | *0 = Sensor check enabled (default) | ||