1,122
edits
m (→Section: Station: Corrected build number for Sync FO Reads) |
(→Section: Station: Remove beta 1.9.3 references) |
||
Line 344: | Line 344: | ||
|- | |- | ||
|DavisCalcAltPress=1 | |DavisCalcAltPress=1 | ||
|Davis stations calculate Sea Level Pressure from Station Pressure using a formula based on several parameters such as temperature, humidity, etc, rather than just using altitude as most other stations. CWOP require 'Altimeter Pressure' to be uploaded, i.e. a value calculated simply using altitude. The station does not provide this value directly, nor the station pressure, so Cumulus has to read some extra data once a minute in order to do the calculation. This can take several seconds, so it means that a 'normal' data reading may be missed. | |Davis stations calculate Sea Level Pressure from Station Pressure using a formula based on several parameters such as temperature, humidity, etc, rather than just using altitude as most other stations. CWOP require 'Altimeter Pressure' to be uploaded, i.e. a value calculated simply using altitude. The station does not provide this value directly, nor the station pressure, so Cumulus has to read some extra data once a minute in order to do the calculation. This can take several seconds, so it means that a 'normal' data reading may be missed. | ||
Line 353: | Line 352: | ||
|- | |- | ||
|UVdecimals=1 | |UVdecimals=1 | ||
|UV values are now displayed and logged as whole numbers by default. You can change this by adding this entry specifying the number of decimal places. | |UV values are now displayed and logged as whole numbers by default. You can change this by adding this entry specifying the number of decimal places. | ||
*0 = Integer Values (default) | *0 = Integer Values (default) | ||
Line 359: | Line 357: | ||
|- | |- | ||
|NoSensorCheck=1 | |NoSensorCheck=1 | ||
|The option (for 'incomplete' stations) to disable the sensor check described in this [http://wiki.sandaysoft.com/a/FAQ#Cumulus_isn.27t_performing_periodic_tasks.2C_like_data_logging_or_web_uploads FAQ] | |The option (for 'incomplete' stations) to disable the sensor check described in this [http://wiki.sandaysoft.com/a/FAQ#Cumulus_isn.27t_performing_periodic_tasks.2C_like_data_logging_or_web_uploads FAQ] | ||
*0 = Sensor check enabled (default) | *0 = Sensor check enabled (default) | ||
Line 365: | Line 362: | ||
|- | |- | ||
|RG11port=1 | |RG11port=1 | ||
|Specifies the COM port to use for Hydreon RG-11 rain detection devices. 1 = COM1 | |Specifies the COM port to use for Hydreon RG-11 rain detection devices. 1 = COM1 | ||
|- | |- | ||
|RG11TBRmode=1 | |RG11TBRmode=1 | ||
|Specifies the Hydreon RG-11 rain device mode of operation. | |Specifies the Hydreon RG-11 rain device mode of operation. | ||
*0 = Rain detection mode - "It's Raining" | *0 = Rain detection mode - "It's Raining" | ||
Line 375: | Line 370: | ||
|- | |- | ||
|RG11tipsize=0.01 | |RG11tipsize=0.01 | ||
|Specifies the tipping bucket size for Hydreon RG-11 rain detection devices. The 'tip size' must be specified in the units that you have configured Cumulus to use for rain. | |Specifies the tipping bucket size for Hydreon RG-11 rain detection devices. The 'tip size' must be specified in the units that you have configured Cumulus to use for rain. | ||
|- | |- | ||
Line 383: | Line 377: | ||
RG11tipsize2= | RG11tipsize2= | ||
|Settings to connect a second Hydreon RG-11 rain detection device. | |Settings to connect a second Hydreon RG-11 rain detection device. | ||
Note that you must have one RG-11 set to "It's raining" mode and the other to "tipping bucket" mode. Cumulus does not validate this. | Note that you must have one RG-11 set to "It's raining" mode and the other to "tipping bucket" mode. Cumulus does not validate this. | ||
|- | |- | ||
|SyncFOReads=1 | |SyncFOReads=1 | ||
|Specifies the Fine Offset synchronisation mode of operation. | |Specifies the Fine Offset synchronisation mode of operation. | ||
*0 = default | *0 = default |