Cumulus Wiki

Cumulus.ini (preserving history): Difference between revisions

Cumulus.ini (preserving history) (view source)

Revision as of 00:06, 28 August 2009

11,643 bytes added ,  00:06, 28 August 2009
no edit summary
No edit summary
No edit summary
Line 25: Line 25:
|-
|-
|Port=0  
|Port=0  
|
|Com port in your computer which is connected to your weather station if connected via a serial port.  Defaults to port 0.
|-
|-
|Latitude=0  
|Latitude=0  
Line 50: Line 50:
|-
|-
|Humidity98Fix=0  
|Humidity98Fix=0  
|
|Selected in the Station Configuration Screen Settings block.
*0 = Disabled (default)
*1 = Enabled, humidity displayed and recorded as 100% if your  sensor registers a relative humidity of 98% or greater.  Normally only useful for Oregon Scientific stations.
|-
|-
|Wind10MinAverage=0  
|Wind10MinAverage=0  
|
|Selected in the Station Configuration Screen Settings block.
*0 = Disabled (default)
*1 = Enabled, Cumulus will calculate and display a 10-minute average wind speed instead of using the value supplied by the station.
|-
|-
|CalculatedDP=0  
|CalculatedDP=0  
|
|Selected in the Station Configuration Screen Settings block.
*0 = Disabled
*1 =  Enabled, Cumulus will calculate the dew point instead of using the value supplied by the station. This avoids the restriction in the Oregon Scientific stations where the dew point can never be below freezing point.
 
|-
|-
|CalculatedWC=0  
|CalculatedWC=0  
|
|Selected in the Station Configuration Screen Settings block.
*0 = Disabled
*1 = Enabled, Cumulus will calculate the wind chill instead of using the value supplied by the station. Note that some stations (Fine Offset, for example, do not supply a wind chill value anyway, so Cumulus always calculates it). You should set this if you have specified any calibration values for wind or temperature, so that Cumulus can also apply those values to the wind chill.
|-
|-
|RolloverHour=0  
|RolloverHour=0  
Line 202: Line 211:
|-
|-
|CloudBaseInFeet=1  
|CloudBaseInFeet=1  
|
|Cloud base measurement unit
*0 = meters
*1 = feet (default)
|-
|-
|[Web Site]  
|[Web Site]  
Line 217: Line 228:
|-
|-
|Host=  
|Host=  
|
|This is the name (or the IP address) of the ftp server which you connect to when you upload pages to your web site
|-
|-
|Port=21  
|Port=21  
|
|Port used for FTP upload, default =21
|-
|-
|Username=  
|Username=  
Line 226: Line 237:
|-
|-
|Password=  
|Password=  
|your web site FTP login password as entered in the Internet Configuration Screen
|your web site FTP login password as entered in the Internet Configuration Screen (note: this is not encrypted)
|-
|-
|Directory=  
|Directory=  
|
|Directory (including path)on your server to which FTP will upload the files
|-
|-
|AutoUpdate=0  
|AutoUpdate=0  
|
|Set in the Internet Configuration Screen Web Settings block.
*0 = Disabled
*1 = Enabled, Cumulus will automatically upload your updated web pages to your web site at regular intervals (as specified by the 'Update Interval')
|-
|-
|ActiveFTP=0  
|ActiveFTP=0  
|
|Set in the Internet Configuration Screen Web Settings block.
*0 = Disabled
*1 = Enabled, Cumulus will use 'active' FTP mode instead of the default 'passive' mode. You should only select active mode if you are having problems with FTP uploads.
|-
|-
|EnableRealtime=0  
|EnableRealtime=0  
|
|Set in the Internet Configuration Screen Web Settings block.
*0 = Disabled
*1 = Enabled, Cumulus will upload a file called realtime.txt to your web site, at the interval specified by Realtime Interval (see below). This file contains various weather parameters and is used by the CumulusRealtime.swf real time wind gauges (as on the supplied 'gauges' web page. If you don't have this option selected, but do have the 'auto update' option set (and a suitable interval configured), Cumulus will still create the realtime.txt file at the specified Interval (not the Realtime Interval) so that you can specify it as an extra file to upload during the 'normal' upload, or use it for any other purpose on your PC.
|-
|-
|RealtimeInterval=3000  
|RealtimeInterval=3000  
|
|Set in the Internet Configuration Screen Web Settings block. The time in seconds between uploads of the realtime.txt file.
|-
|-
|UpdateInterval=15  
|UpdateInterval=15  
|
|Set in the Internet Configuration Screen Web Settings block.  The interval in minutes at which you wish auto updates to occur.
|-
|-
|IncludeSTD=1  
|IncludeSTD=1  
|
|Selected in the Internet Configuration Files Tab screen
*0 = Disabled
*1 = Enabled, (default) the standard web files provided with Cumulus will be processed and uploaded at each web update.
|-
|-
|IncludeSTDImages=1  
|IncludeSTDImages=1  
|
|Selected in the Internet Configuration Files Tab screen
*0 = Disabled
*1 = Enabled,(default) the standard image files generated by Cumulus (graphs, etc) will be uploaded at each web update.
|-
|-
|FTPRename=0  
|FTPRename=0  
|
|Selected in the Internet Configuration Files Tab screen
*0 = Disabled
*1 = Enabled,
|-
|-
|DeleteBeforeUpload=0  
|DeleteBeforeUpload=0  
|
*0 = Disabled
*1 = Enabled,
|-
|-
|ResizeGraphs=0  
|ResizeGraphs=0  
Line 274: Line 298:
|-
|-
|ExtraLocal0=  
|ExtraLocal0=  
|
|Path and file name on local computer for alternate file #0. Set in Internet Configuration Screen Files tab.
|-
|-
|ExtraRemote0=  
|ExtraRemote0=  
|
|Path and file name on web server for alternate file #0. Set in Internet Configuration Screen Files tab.
|-
|-
|ExtraProcess0=0  
|ExtraProcess0=0  
|
|Set in Internet Configuration Screen Files tab.
|-
|-
|ExtraBinary0=0  
|ExtraBinary0=0  
|
|Set in Internet Configuration Screen Files tab.
*0 = not binary (e.g. HTML file)
*1 = Binary (e.g. images)
|-
|-
|ExtraRealtime0=0  
|ExtraRealtime0=0  
|
|Set in Internet Configuration Screen Files tab. If you select this for any files, you will also need to select the Realtime option.
*0 = Disabled, (default) file uploaded as part of normal upload
*1 = Enabled, file uploaded during Realtime upload
 
|-
|-
|ExtraFTP0=1  
|ExtraFTP0=1  
|
|Set in Internet Configuration Screen Files tab.
*0 = Disabled, File copied to the location specified in the Remote Filename box.
*1 = Enabled, (default) File uploaded  by FTP
|-
|-
|ExtraLocal1=  
|ExtraLocal1=  
|
|Path and file name on local computer for alternate file #1. Set in Internet Configuration Screen Files tab.
|-
|-
|ExtraRemote1=  
|ExtraRemote1=  
|
|Path and file name on web server for alternate file #1. Set in Internet Configuration Screen Files tab.
|-
|-
|ExtraProcess1=0  
|ExtraProcess1=0  
|
|Set in Internet Configuration Screen Files tab.
|-
|-
|ExtraBinary1=0  
|ExtraBinary1=0  
|
|Set in Internet Configuration Screen Files tab.
*0 = not binary (e.g. HTML file)
*1 = Binary (e.g. images)
|-
|-
|ExtraRealtime1=0  
|ExtraRealtime1=0  
|
|Set in Internet Configuration Screen Files tab. If you select this for any files, you will also need to select the Realtime option.
*0 = Disabled, (default) file uploaded as part of normal upload
*1 = Enabled, file uploaded during Realtime upload
 
|-
|-
|ExtraFTP1=1  
|ExtraFTP1=1  
|
|Set in Internet Configuration Screen Files tab.
*0 = Disabled, File copied to the location specified in the Remote Filename box.
*1 = Enabled, (default) File uploaded  by FTP
|-
|-
|ExtraLocal2=  
|ExtraLocal2=  
|
|Path and file name on local computer for alternate file #2. Set in Internet Configuration Screen Files tab.
|-
|-
|ExtraRemote2=  
|ExtraRemote2=  
|
|Path and file name on web server for alternate file #2. Set in Internet Configuration Screen Files tab.
|-
|-
|ExtraProcess2=0  
|ExtraProcess2=0  
|
|Set in Internet Configuration Screen Files tab.
*0 = Disabled
*1 = Enabled,
|-
|-
|ExtraBinary2=0  
|ExtraBinary2=0  
|
|Set in Internet Configuration Screen Files tab.
*0 = not binary (e.g. HTML file)
*1 = Binary (e.g. images)
|-
|-
|ExtraRealtime2=0  
|ExtraRealtime2=0  
|
|Set in Internet Configuration Screen Files tab. If you select this for any files, you will also need to select the Realtime option.
*0 = Disabled, (default) file uploaded as part of normal upload
*1 = Enabled, file uploaded during Realtime upload
 
|-
|-
|ExtraFTP2=1  
|ExtraFTP2=1  
|
|Set in Internet Configuration Screen Files tab.
*0 = Disabled, File copied to the location specified in the Remote Filename box.
*1 = Enabled, (default) File uploaded  by FTP
|-
|-
|ExtraLocal3=  
|ExtraLocal3=  
|
|Path and file name on local computer for alternate file #3. Set in Internet Configuration Screen Files tab.
|-
|-
|ExtraRemote3=  
|ExtraRemote3=  
|
|Path and file name on web server for alternate file #3. Set in Internet Configuration Screen Files tab.
|-
|-
|ExtraProcess3=0  
|ExtraProcess3=0  
|
|Set in Internet Configuration Screen Files tab.
*0 = Disabled
*1 = Enabled,
|-
|-
|ExtraBinary3=0  
|ExtraBinary3=0  
|
|Set in Internet Configuration Screen Files tab.
*0 = not binary (e.g. HTML file)
*1 = Binary (e.g. images)
|-
|-
|ExtraRealtime3=0  
|ExtraRealtime3=0  
|
|Set in Internet Configuration Screen Files tab. If you select this for any files, you will also need to select the Realtime option.
*0 = Disabled, (default) file uploaded as part of normal upload
*1 = Enabled, file uploaded during Realtime upload
 
|-
|-
|ExtraFTP3=1  
|ExtraFTP3=1  
|
|Set in Internet Configuration Screen Files tab.
*0 = Disabled, File copied to the location specified in the Remote Filename box.
*1 = Enabled, (default) File uploaded  by FTP
|-
|-
|ExtraLocal4=  
|ExtraLocal4=  
|
|Path and file name on local computer for alternate file #4. Set in Internet Configuration Screen Files tab.
|-
|-
|ExtraRemote4=  
|ExtraRemote4=  
|
|Path and file name on web server for alternate file #4. Set in Internet Configuration Screen Files tab.
|-
|-
|ExtraProcess4=0  
|ExtraProcess4=0  
|
|Set in Internet Configuration Screen Files tab.
*0 = Disabled
*1 = Enabled,
|-
|-
|ExtraBinary4=0  
|ExtraBinary4=0  
|
|Set in Internet Configuration Screen Files tab.
*0 = not binary (e.g. HTML file)
*1 = Binary (e.g. images)
|-
|-
|ExtraRealtime4=0  
|ExtraRealtime4=0  
|
|Set in Internet Configuration Screen Files tab. If you select this for any files, you will also need to select the Realtime option.
*0 = Disabled, (default) file uploaded as part of normal upload
*1 = Enabled, file uploaded during Realtime upload
 
|-
|-
|ExtraFTP4=1  
|ExtraFTP4=1  
|
|Set in Internet Configuration Screen Files tab.
*0 = Disabled, File copied to the location specified in the Remote Filename box.
*1 = Enabled, (default) File uploaded  by FTP
|-
|-
|ExtraLocal5=  
|ExtraLocal5=  
|
|Path and file name on local computer for alternate file #5. Set in Internet Configuration Screen Files tab.
|-
|-
|ExtraRemote5=  
|ExtraRemote5=  
|
|Path and file name on web server for alternate file #5. Set in Internet Configuration Screen Files tab.
|-
|-
|ExtraProcess5=0  
|ExtraProcess5=0  
|
|Set in Internet Configuration Screen Files tab.
*0 = Disabled
*1 = Enabled,
|-
|-
|ExtraBinary5=0  
|ExtraBinary5=0  
|
|Set in Internet Configuration Screen Files tab.
*0 = not binary (e.g. HTML file)
*1 = Binary (e.g. images)
|-
|-
|ExtraRealtime5=0  
|ExtraRealtime5=0  
|
|Set in Internet Configuration Screen Files tab. If you select this for any files, you will also need to select the Realtime option.
*0 = Disabled, (default) file uploaded as part of normal upload
*1 = Enabled, file uploaded during Realtime upload
 
|-
|-
|ExtraFTP5=1  
|ExtraFTP5=1  
|
|Set in Internet Configuration Screen Files tab.
*0 = Disabled, File copied to the location specified in the Remote Filename box.
*1 = Enabled, (default) File uploaded  by FTP
|-
|-
|ExtraLocal6=  
|ExtraLocal6=  
|
|Path and file name on local computer for alternate file #6. Set in Internet Configuration Screen Files tab.
|-
|-
|ExtraRemote6=  
|ExtraRemote6=  
|
|Path and file name on web server for alternate file #6. Set in Internet Configuration Screen Files tab.
|-
|-
|ExtraProcess6=0  
|ExtraProcess6=0  
|
|Set in Internet Configuration Screen Files tab.
*0 = Disabled
*1 = Enabled,
|-
|-
|ExtraBinary6=0  
|ExtraBinary6=0  
|
|Set in Internet Configuration Screen Files tab.
*0 = not binary (e.g. HTML file)
*1 = Binary (e.g. images)
|-
|-
|ExtraRealtime6=0  
|ExtraRealtime6=0  
|
|Set in Internet Configuration Screen Files tab. If you select this for any files, you will also need to select the Realtime option.
*0 = Disabled, (default) file uploaded as part of normal upload
*1 = Enabled, file uploaded during Realtime upload
 
|-
|-
|ExtraFTP6=1  
|ExtraFTP6=1  
|
|Set in Internet Configuration Screen Files tab.
*0 = Disabled, File copied to the location specified in the Remote Filename box.
*1 = Enabled, (default) File uploaded  by FTP
|-
|-
|ExtraLocal7=  
|ExtraLocal7=  
|
|Path and file name on local computer for alternate file #7. Set in Internet Configuration Screen Files tab.
|-
|-
|ExtraRemote7=  
|ExtraRemote7=  
|
|Path and file name on web server for alternate file #7. Set in Internet Configuration Screen Files tab.
|-
|-
|ExtraProcess7=0  
|ExtraProcess7=0  
|
|Set in Internet Configuration Screen Files tab.
*0 = Disabled
*1 = Enabled,
|-
|-
|ExtraBinary7=0  
|ExtraBinary7=0  
|
|Set in Internet Configuration Screen Files tab.
*0 = not binary (e.g. HTML file)
*1 = Binary (e.g. images)
|-
|-
|ExtraRealtime7=0  
|ExtraRealtime7=0  
|
|Set in Internet Configuration Screen Files tab. If you select this for any files, you will also need to select the Realtime option.
*0 = Disabled, (default) file uploaded as part of normal upload
*1 = Enabled, file uploaded during Realtime upload
 
|-
|-
|ExtraFTP7=1  
|ExtraFTP7=1  
|
|Set in Internet Configuration Screen Files tab.
*0 = Disabled, File copied to the location specified in the Remote Filename box.
*1 = Enabled, (default) File uploaded  by FTP
|-
|-
|ExtraLocal8=  
|ExtraLocal8=  
|
|Path and file name on local computer for alternate file #8. Set in Internet Configuration Screen Files tab.
|-
|-
|ExtraRemote8=  
|ExtraRemote8=  
|
|Path and file name on web server for alternate file #8. Set in Internet Configuration Screen Files tab.
|-
|-
|ExtraProcess8=0  
|ExtraProcess8=0  
|
|Set in Internet Configuration Screen Files tab.
*0 = Disabled
*1 = Enabled,
|-
|-
|ExtraBinary8=0  
|ExtraBinary8=0  
|
|Set in Internet Configuration Screen Files tab.
*0 = not binary (e.g. HTML file)
*1 = Binary (e.g. images)
|-
|-
|ExtraRealtime8=0  
|ExtraRealtime8=0  
|
|Set in Internet Configuration Screen Files tab. If you select this for any files, you will also need to select the Realtime option.
*0 = Disabled, (default) file uploaded as part of normal upload
*1 = Enabled, file uploaded during Realtime upload
 
|-
|-
|ExtraFTP8=1  
|ExtraFTP8=1  
|
|Set in Internet Configuration Screen Files tab.
*0 = Disabled, File copied to the location specified in the Remote Filename box.
*1 = Enabled, (default) File uploaded  by FTP
|-
|-
|ExtraLocal9=  
|ExtraLocal9=  
|
|Path and file name on local computer for alternate file #9. Set in Internet Configuration Screen Files tab.
|-
|-
|ExtraRemote9=  
|ExtraRemote9=  
|
|Path and file name on web server for alternate file #9. Set in Internet Configuration Screen Files tab.
|-
|-
|ExtraProcess9=0  
|ExtraProcess9=0  
|
|Set in Internet Configuration Screen Files tab.
*0 = Disabled
*1 = Enabled,
|-
|-
|ExtraBinary9=0  
|ExtraBinary9=0  
|
|Set in Internet Configuration Screen Files tab.
*0 = not binary (e.g. HTML file)
*1 = Binary (e.g. images)
|-
|-
|ExtraRealtime9=0  
|ExtraRealtime9=0  
|
|Set in Internet Configuration Screen Files tab. If you select this for any files, you will also need to select the Realtime option.
*0 = Disabled, (default) file uploaded as part of normal upload
*1 = Enabled, file uploaded during Realtime upload
|-
|-
|ExtraFTP9=1  
|ExtraFTP9=1  
|
|Set in Internet Configuration Screen Files tab.
*0 = Disabled, File copied to the location specified in the Remote Filename box.
*1 = Enabled, (default) File uploaded  by FTP
|-
|-
|[Display]  
|[Display]  
Retrieved from "https://www.cumuluswiki.org/a/Special:MobileDiff/205"