Cumulus.ini (preserving history): Difference between revisions

{{TOCright}}

= Introduction =

== Creating Configuration File ==

When you download Cumulus 1 or MX, ''there is no configuration file included in the download''. So when you first use the software, either flavour of Cumulus, you will need to enter some settings, and that will lead to creation of the main configuration file. How to enter these minimum settings will be described next.

#If you start Cumulus MX without a configuration file, and you have a screen attached so you can see the output from the engine, it will show this: [[File:MX first start.PNG]]

#As you can see, it is running, but it does not know what station type, so it cannot connect to it, and will not do anything more.

#Open the user interface, and select the station settings if necessary: [[File:MX_station_settings.png|800px|center]]

#At the very minimum, you must select a station type and units (as shown in image here)

# If you have a screen attached to the device running the MX engine, you can click in that screen and terminate Cumulus MX. Otherwise do whatever is needed to end the MX executable on your installation. This is the action that will create the main configuration file.

#Restart Cumulus MX, it will read the configuration file, find the weather station, and start reading the weather data from it. On this first access to your weather station, it will not read any archive data, just the live data while MX remains running.

 

== Swapping from Cumulus 1 to MX ==

== Configuration File names ==

=== Cumulus 1 ===

 

 

= Upgrading to New Build =

Installing a new build of Cumulus (whatever version) over the existing installation does not affect this settings file. No build of Cumulus contains a 'Cumulus.ini' file. If Cumulus software detects a 'Cumulus.ini' when it starts, it looks in that for settings; if it does not find the file, then Cumulus will expect you to tell it some settings, others have defaults. See Cumulus Help, release announcement, and other provided documentation for more.

 

= File Structure =

 

Some [[#Sections_dealing_with_interfaces_to_external_sites|sections]] relate to the external websites that Cumulus can optionally supply with updates. These are set by configuration screens and the whole sections will always be present. If you do not use those external services their parameters will be set to the defaults.

 

== Completeness of this list ==

If you spot a parameter that is missing from this list (check you are looking in the right section, and under the correct sub-heading where a section is sub-divided for ease of using this article), then please add it to this Wiki article. None of the authors who have contributed so far can claim completeness. Sometimes a search on the forum for something else reveals a mention of an additional parameter that can be added to the file but has not been previously added to this list.

 

 

== Beta builds ==

 

 

 

= Editing the file =

 

== Initialisation ==

 

 

 

Many configuration parameter lines are changed from the various application edit, view, or configuration screens, and so making any amendments using those screens should ensure your replacement values are acceptable. You should never edit these parameter lines directly in the file ''while Cumulus is running'', as when Cumulus shuts down it will replace your amendments to these parameters with the contents of the relevant application Edit/View/Configuration screens.

 

 

''You can edit them in the file with Cumulus stopped'', but beware of selecting invalid values for these parameters, generally it is safer to use the application to edit them (unless you are importing values from another setup), and Cumulus will read the new values when it is next restarted.

=== Editing outside Cumulus ===

*If your system is configured to use a comma for a decimal separator, then you should use a comma in any decimal values that you set in this file.

*You should use a simple text editor (not a rich text editor nor word processor) to edit this file as only letters, numerical digits, decimal separators and the equals symbol are allowed in any parameter. If you use a spreadsheet program to make use of the manipulation it offers, ensure it is set to output in pure text.

 

= File Contents =

 

{| class="wikitable" border="1"

|-

|-

|style="background:lightgray;"|[Station]

|-

|Type= -1

|Station Type as set by the checked radio box in the [[Cumulus_Screenshots#Configuration_Menu_Screens|Station Configuration Screen]], Station Type block. For details of [[Supported_Devices]] click that link.

*0=Vantage Pro station

*1=Vantage Pro2 station

*3=WM-918 station

For Oregon Scientific stations and similar re-badged stations (Huger, Radio Shack etc) which have a serial port connection, if your model is not listed, try WM-918 if your station has wired connections, and WMR-928 if it is wireless.

 

*4=Reading from file [[EasyWeather_Format#Usage_of_easyweather.dat_fields_for_Cumulus_input_of_latest_record: |EasyWeather.dat]] (using EasyWeather software version 6.2, or earlier, running continuously with Cumulus). Fine Offset weather stations that record Solar and UV measurements output to [[EasyWeather_Format#EasyWeatherPlus.dat| EasyWeatherPlus.dat file]] when Easyweather software version 6.x is running. This has the same fields as easyweather.dat, plus two extra fields for Solar and UV data at the end, and so Cumulus can understand the fields you must also have '''LogExtraSensors=1''' set.

*6=WS2300 (For all La Crosse WS23xx models)

*8=[[WMR100-200_Protocol|WMR100]]

*9=[[WMR100-200_Protocol|WMR200]]

*10=Instromet (with optional extra solar sensors or without)

|-

|Model="your Model description"

|-

|-

|Latitude=0

|-

|Longitude=0

|-

|LatTxt=

|-

|LonTxt=

|-

|Altitude=0

|-

|AltitudeInFeet=1

*0 = metres Above Sea Level

*1 = feet ASL

|-

|Wind10MinAverage=0

*0 = Disabled (default), Cumulus will display the value supplied by the station. This is a 10 minute average for Davis stations, but an average over a shorter period for Oregon Scientific and Fine Offset stations, see [[FAQ#Cumulus_is_showing_a_different_wind_speed_compared_to_my_console]].

*1 = Enabled, Cumulus will calculate and display a N-minute average wind speed where N is defined by the previous parameter if present, otherwise defaults to 10, the international standard duration used to calculate average wind speeds.

|-

|UseSpeedForAvgCalc=0

*0 = Disabled (default), Cumulus will display the average wind speed value supplied by the station, see [[FAQ#Cumulus_is_showing_a_different_wind_speed_compared_to_my_console]].

*1 = Enabled, Cumulus will use the longer-term 'speed' values in the average speed calculation. The preceding 'Wind10MinAverage' option must be enabled for this parameter to have any effect.

|-

|RoundWindSpeed=0

*0 = Disabled (default), Cumulus will display the wind speed value to the precision used by the station.

*1 = Enabled, this setting causes wind speeds to be rounded to the nearest integer.

|-

|UseZeroBearing=0

*0 = Disabled, Cumulus displays the current bearing read from the station (i.e. the last direction the wind was blowing from before it became calm). Note that the average wind bearing will always display zero bearing if there has been no wind for the last N minutes (where N is defined by previous parameter if present but defaults to 10), as the average bearing takes wind speed into account.

*1 = Enabled, Cumulus display a bearing of zero (and '---' for the compass point) when the wind is calm (note when not calm, bearing is 360 for true North)

|-

|CalculatedDP=0

*0 = Disabled, Cumulus will display the dew point value supplied by the station.

*1 = Enabled, Cumulus will calculate the dew point instead. This avoids the restriction in the Oregon Scientific stations where the dew point can never be below freezing point.

|-

|CalculatedWC=0

*0 = Disabled

*1 = Enabled, Cumulus will calculate the wind chill instead of using the value supplied by the station. You should set this if you have specified any calibration values for wind and/or temperature, so that Cumulus can also apply those adjustments to the wind chill.

Note that some stations (Fine Offset, for example), do not make a wind chill value available to Cumulus. For these, Cumulus always calculates it.

|-

|RolloverHour=0

*0 = midnight

*9 = 9am/10am

|-

|Use10amInSummer=1

*0 = Use 9am in summer (use 10am not checked on Station Configuration Screen)

*1 = Use 10am in summer selected on Station Configuration Screen

|-

|WarnMultiple=0

*0 = Disabled, (default) Multiple instances allowed.

*1 = Enabled, prevents multiple instances of Cumulus from running.

|-

|ConfirmClose=0

*0 = Disabled, application will close immediately

*1 = Enabled, application will prompt for confirmation that you wish to close it (do not use this if you might suspend/standby/hibernate your computer)

|-

|CloseOnSuspend=1

*0 = Disabled, application will not close if you suspend/standby/hibernate your computer (it is highly recommended you close Cumulus manually before your computer is put into suspend/standby/hibernate state)

*1 = Enabled, application will close on suspend/standby/hibernate of your computer (recommended if your computer can go into any of these states when left alone)

|-

|DataLogInterval=2

*0 = 1 min

*1 = 5 mins

*4 = 20 mins

*5 = 30 mins

*For other makes as ''Cumulus on restarting is able (see next parameter) to read logged data from your station'' you can choose to match Cumulus and station logging intervals, then the frequency of logged information will be same regardless of whether Cumulus is running continuously or restarted (this improves accuracy of any averages calculated).

|-

|UseDataLogger=1

*0 = Disabled, at start-up, Cumulus will not download data from the station's data logger (if it has one) but just start with next observations.

*1 = Enabled (Default), at start-up Cumulus will download data from the station's data logger (if it has one) to catch up from the point where Cumulus was last shut down. See last parameter for advice re station logging interval.

*0 = m/s

*1 = mph

*3 = kts

|-

|PressureUnit=0

*1 = hPa

*2 = in

|-

|RainUnit=0

*0 = mm

*1 = in

|-

|TempUnit=0

*0 = Celsius

*1 = Fahrenheit

|-

|LocName=

|-

|LocDesc=

|-

|LastLoggerDownload=13/08/2008 12:48:52

|-

|RainSeasonStart=1

|-

|YTD[[FAQ#My_monthly_and.2For_annual_rainfall_totals_are_wrong|rain]]=0

|-

|YTDrainyear=0

|-

|UseCumulusForecast=0

*0 = Disabled (default)

*1 = Enabled

|-

|HourlyForecast=0

*0 = Disabled, (default) Cumulus will use Zambretti Forecaster every time it updates the web pages.

*1 = Enabled, this setting causes the forecast to be updated only once an hour (on the hour).

|-

|UseCumulusPresstrendstr=0

*0 = Disabled

*1 = Enabled

|-

|FCpressinMB=1

*0 = inches of mercury

*1 = mb

|-

|FClowpress=950

|-

|FChighpress=1050

|-

|CloudBaseInFeet=1

*0 = metres

*1 = feet (default)

|-

|-

|-

 

|-

|-

|-

|}

 

==== Davis family specific: ====

 

 

{| class="wikitable" border="1"

|-

|style="background:lightgray;"|Section name - the following parameters relate to the station configuration.

|-

|-

|ForceVPBarUpdate=0

|-

|ClockSettingHour=4

*4 = 04:00 (default value)

*0-23 = 00:00 to 23:00

*(1 = usb - setting no longer available on screen, remains as default in cumulus.ini for those not using a Davis)

*2 = TCP/IP (see later parameters to specify ports)

|-

|VP2TCPPort=22222

|Set this in the Station Configuration Screen '''Davis TCP/IP Settings''' block.

Weather station IP address if VP type has TCP/IP selected. Default is 0.0.0.0

|-

|VP2PeriodicDisconnectInterval=0

 

Set it to zero to disable, if you are not using the Weatherlink site.

|-

|LogExtraSensors=0

|This is set in the '''Settings''' block on the Station settings screen off the configuration menu. Set this to 1 if you have additional sensors (e.g. a Davis Leaf Wetness probe) to make Cumulus read, display, and log the readings from the sensors. You don't select this for Solar/UV sensors.

|-

|RestartIfDataStops=0

|This parameter (attribute=value) is added directly to the file, it does not appear on a configuration screen.

|}

 

====Introduced for problems with Fine Offset family:====

*Some parameters are set on screens, other attributes do not appear in the '''cumulus.ini''' file unless they are added using an external editor, but the values still have a recommended default value as explained below.

 

{| class="wikitable" border="1"

|style="background:lightgray;"|Section name - the following parameters relate to the station configuration.

|-

|-

|FOReadAvoidPeriod=3

|Add this line to cumulus.ini [Station] section if you wish to change the default, this parameter used to fine-tune the previous parameter.

*3 = default value

 

|-

|ReportLostSensorContact=0

*1 = reporting on (default)

Option to turn off reporting of 'lost sensor contact' for Fine Offset stations. (added Cumulus 1.9.4 b.1070)

|-

|EWdisablecheckinit=0

*1 = Ignores part of memory (see [[FAQ#When_I_start_Cumulus.2C_I_get_the_error_message_.22The_station_is_not_initialised.22]]).

 

|-

|EWduplicatecheck=0

For example one problem is that "55 AA" repeats at the start of the second line of data. Those bytes are only supposed to appear at the start of the first line (or so I am told).

 

|-

|EWpressureoffset=x.y

Got a pressure problem with a Fine Offset station when the pressure 'offset' that Cumulus reads is garbage, so Cumulus just uses zero?

 

 

|}

 

|}

 

 

*Stations not recognised by Cumulus ''may'' be set to create an [[EasyWeather_Format#Usage_of_easyweather.dat_fields_for_Cumulus_input_of_latest_record: |EasyWeather_Format]] file. For these the first two (or three) parameters below are mandatory.

{| class="wikitable" border="1"

 

==== Oregon Scientific specific: ====

{| class="wikitable" border="1"

|-

*1= Enabled - Used for Oregon Scientific WMR-928 and similar stations if you have additional sensors (e.g. another temperature probe) to make Cumulus read, display, and log the readings from those sensors. You don't use this for Solar/UV sensors.

(Note this attribute appears in [[#Davis_family_specific|Davis family]] and [[#Introduced_for_problems_with_Fine_Offset_family:|Fine Offset family]] tables above and in [[#Instromet_station_specific:|Instromet station specific:]] table below with different usage explanations).

|-

|WMR928TempChannel=N

|style="background:lightgray;"|[Station]

|style="background:lightgray;"|Section name - the following parameters relate to the station configuration.

|-

|WS2300Sync=1

|-

|RestartIfDataStops=0

Option for Cumulus 1, it attempts to restart itself if it has had no data from a La Crosse station for 60 seconds i.e. if data from station stops. This may fix whatever the problem is; it may not. But it should at least stop the same data being repeatedly logged.

*0 = Disabled (default)

Note that you must have one RG-11 set to "It's raining" mode and the other to "tipping bucket" mode. Cumulus does not validate this.

|}

 

==== Instromet station specific: ====

|style="background:lightgray;"|[Station]

|style="background:lightgray;"|Section name - the following parameters relate to the station configuration.

|-

|ImetWaitTime=200

|This parameter (attribute=value) if you need to change it from its '''default of 200 ms''' is added directly to the file, it does not appear on a configuration screen.

Specifies the time in milliseconds that Cumulus allows for a response from an Instromet station. If you are having problems with reading from an Instromet station, try inserting this line into the ''Station'' section using a value of 500. According to the specification, 500 ms is the absolute maximum time that the station should take to respond to any command.

|-

|SyncDavisClock=0

|}

 

{| class="wikitable" border="1"

|-

|style="background:lightgray;"|Section Name - the following 'attribute=value' parameters are the adjustment factors for your specific sensors

|-

|-

|TempOffset=Offset_Value

|-

|TempMult=1

|First order multiplier by which measured outdoor Temperature is to be corrected (default=1).

|-

|-

|HumOffset=Offset_Value

|-

|WindDirOffset=Offset_Value

|Multiplier by which measured [[Wind_measurement#Wind_Speed|Wind Gust]] Speed is to be corrected (default=1).

|-

|-

|RainMult=1

|Multiplier by which measured Rainfall (and therefore rainfall rate too) is to be corrected (default=1).

|-

|UVOffset=Offset_Value

|-

|}

 

{| class="wikitable" border="1"

|-

|}

 

 

See individual entries for how to modify these parameters (either select on a screen, or edit file directly). Where the modification can be done on a screen, the Cumulus Help screens (e.g. Configuration: Internet) will explain the selection.

 

{| class="wikitable" border="1"

|-

!style="width:150px" | Parameter Line Entry

|-

|style="background:lightgray;"|[FTP site]

|style="background:lightgray;"|Section Name - the following parameters relate to your website FTP parameters

|-

|DailyProgram=

*default - none

|-

|DailyParams=

*default - none

The corresponding 'parameters' for 'DailyProgram' used to specify any parameters to be passed to that command.

|-

|Host=

''If you host your web site yourself, then "'''Host=localhost'''" might be appropriate''.

 

|-

|Port=21

Port used for FTP upload, default as shown is the normal port.

|-

|Username=

|-

|Password=

|-

|Directory=

*value is left Blank, default, the root position specified by ftp server (see Host above)

*A path from the starting point as the position specified by ftp server (see Host above)

|-

|IncludeSTD=1

*0 = Disabled

*1 = Enabled, (default) the standard web files provided with Cumulus will be processed and uploaded at each automatic or manual web update to the FTP root or any 'Directory' you have specified (see above).

|-

|AutoUpdate=0

*0 = Disabled, an upload will only occur if ''Web upload'' is selected manually either from the '''File''' menu or the right click menu if Cumulus is minimised.

*1 = Enabled, Cumulus will automatically upload your processed web pages to your web site at regular intervals (as specified by the 'Update ''Interval'' ' - see below) using FTP to the directory as specified in 'Directory' (see above).

|-

|ActiveFTP=0

*0 = Disabled (default)

*1 = Enabled, Cumulus will use 'active' FTP mode instead of the default 'passive' mode. You should only select active mode if you are having problems with FTP uploads.

|-

|FTPRename=0

*0 = Disabled (default), no name change after uploading onto the server

*1 = Enabled, the new update is loaded using temporary names, files are renamed on the sever afterwards

|-

|DeleteBeforeUpload=0

*0 = Disabled (default)

*1 = Enabled, files are deleted from sever before the new update is loaded

|-

|UpdateInterval=15

|-

|ExternalProgram=

|-

|ExternalParams=

|-

|EnableRealtime=0

*0 = Disabled (default)

** - If you do not have ''Auto Update'' option set (top of Web Settings block), the ''realtime.txt'' file is not created/updated.

** - If you have the ''Auto Update'' option set (and a suitable ''Interval'' configured), Cumulus will create the ''realtime.txt'' file at that specified normal update ''Interval'' (not the Real-time Interval)

** It only creates the file (any previous creation is lost) at that interval, but you can separately specify it as an extra file to upload during the 'normal' upload, or just use it for any other purpose on your PC.

|-

|RealtimeFTPEnabled=0

*1 = Enabled, Cumulus will establish an FTP connection to your web site, so that the realtime.txt file, and any other files you specify, can be uploaded when realtime processing takes place.

The 'EnableRealtime' setting must be set to 1 for this setting to have any effect.

|-

|RealtimeTxtFTP=0

When set to 1 Cumulus will upload the [[realtime.txt]] to your web site during realtime processing. The 'EnableRealtime' and 'RealtimeFTPEnabled' settings must both be set to 1 for this setting to have any effect.

|-

|-

|RealtimeProgram=

|-

|RealtimeParams=

|-

|-

|-

|-

|-

|-

|-

|-

|-

|-

|-

|-

|-

|-

|-

 

|-

|-

 

|}

 

 

 

{| class="wikitable" border="1"

|-

|Heading=My Weather

|-

|SavePosition=0

|-

|StartMinimised=0

*0= default, the main window will be displayed on the main or only monitor connected to your pc

*1= If set to 1, Cumulus will start with the main window minimised, either to the system tray or the task bar, depending on the 'MinimizeToTray' setting (see next parameter).

|-

|MinimizeToTray=0

*0 = Disabled (default), Cumulus will minimise to the task bar

*1 = Enabled, causes Cumulus to appear as an icon in the system tray when it is minimized. The icon will flash if a record is broken or an error occurs. Double click on the icon to restore the main window (or right click on the icon and use the pop-up menu).

|-

|ForecastCentred=0

*0 = Disabled, (default) Forecast appears left justified on main screen below sun and moon details

|-

|FontColour=4227327

|-

|BackColour=12632256

|-

|HeadingColour=10485760

|-

|ClockDigitColour=4227327

|-

|ClockColour=16777201

|-

|TwelveHourClock=0

*0 = 24Hr clock mode

*1 - 12 Hr am/pm clock mode

|-

|DisplayCloudBase=0

*0 = Disabled, (default)

*1 = Enabled, the calculated cloud base is displayed on the main screen. The calculation is a simple one; 1000 feet for every 4.5 degrees Fahrenheit difference between the temperature and the dew point.

|-

|DisplayHumidex=0

*0 = Disabled (default) [[Heat_index]] displayed on main screen. The heat index is calculated only if the actual temperature in the shade (not in direct sunlight) is above 27 °C (80 °F), so normal temperature shown here for cooler temperatures.

*1 = Enabled, calculated [[Humidex]] value to be displayed on the main screen instead of Heat Index. (Note that Cumulus displays degrees C or F for Humidex, whereas strictly speaking it is unitless. This is for the convenience of those who use Fahrenheit but would still prefer to see Humidex displayed, where it might be confusing to show the unconverted value.)

|-

|DisplaySolarData=0

*0 = Disabled (default)

*1 = Enabled, adds an extra panel to the main screen below the recent extremes panel - EITHER

|-

|DisplayStormRain=0

*0 = Disabled, (default)

*1 = Enabled, adds an extra output to the main screen to show what Davis stations report as Storm Rain

|-

|LegendSymbolWidth=3

|-

|ChartLineWidth=2

|-

|WindGaugeRange=50

|-

|WindGaugeArcColour=16773091

|-

|WindGaugeAnimated=1

*0 = Disabled,

*1 = Enabled (default)

|-

|WindGaugeAnimationFactor=2

|-

|WindGaugeTickColour=9841920

|-

|WindGaugeFontColour=9841920

|-

|WindGaugeInnerCircleColour=16765615

|-

|WindGaugeNeedleColour=128

|-

|WindGaugeInnerCentreColourFrom=16765615

|-

|WindGaugeInnerCentreColourTo=16765615

|-

|WindGaugeOuterCentreColourFrom=16765357

|-

|WindGaugeOuterCentreColourTo=16711680

|-

|WindGaugeOuterCircleColour=16765615

|-

|WindGaugeOuterRimColour=9470064

|-

|WindGaugeAverageSectorColour=32768

|-

|WindGaugePeakSectorColour=33023

|-

|WindGaugeNeedleShineColourFrom=1049273

|-

|WindGaugeNeedleShineColourTo=328090

|-

|CompassColour=12632256

|-

|CompassTickColour=16711680

|-

|CompassLabelColour=16777215

|-

|CompassBearingColour=0

|-

|CompassCurrentPointerColour=255

|-

|CompassAveragePointerColour=16711680

|-

|WindRoseColour=8388608

|-

|WindRoseLabelColour=0

|-

|WindRoseAxesColour=8388608

|-

|WindRoseTransparency=50

|-

|NumWindRosePoints=16

|-

|TransparentGauges=0

 

The square backgrounds of the three wind gauges on the Cumulus main screen

|-

|TransparentGraphs=0

 

This only works if the graphs are defined to have a solid colour as background (gradient is not selected on ''colours'' configuration screen).

|-

|DigitBackground=0

|-

|LabelColour=0

|-

|AlarmColour=255

|-

|PastAlarmColour=16711680

|-

|PanelHeadingFontColour=0

|-

|PanelLineColour=0

|-

|PanelBorderColour=8421504

|-

|PanelGradientColourFrom=16777215

|-

|PanelGradientColourTo=13226453

|-

|DisplayBeaufortDesc=1

*1 (default), the Beaufort description of the current average wind speed will appear in the header of the wind panel on the main screen.

*0, it will instead appear as a 'tool tip' for the wind panel.

|-

|DisplayBarometerTrendText=1

*1 (default), the description of the current barometer trend will appear in the header of the barometer panel on the main screen.

*0, it will instead appear as a 'tool tip' for the barometer panel.

|-

|UpdateAtStartup=1

*1 (default), the display will be updated as data is downloaded and processed from the station's logger. This increases the time taken to process the data.

*0, it makes the download faster as display is onlyn updated when catch up completed; this may be significant if there is a lot of data to download.

|-

|IndependentGraphsWindow=0

*0 = Disabled (default)

*1 = Enabled

|}

 

 

{| class="wikitable" border="1"

|-

!style="width:150px" | Parameter Line Entry

!style="width:600px" | Function

|-

|style="background:lightgray;"|[Graphs]

|style="background:lightgray;"|Section Name - the following parameters relate to your graph settings

|-

|GraphHours=12

|ChartMaxDays=7

|How many days of values to plot on the daily min/average/max temperature, daily sunshine, and daily rain charts (default=7)

|-

|Background=12632256

|ShowFreezingLine=0

|Draw a horizontal line on the temperature graph at 0°C/32°F

|-

|GraphGradientEnabled=0

|}

 

{| class="wikitable" border="1"

|-

*1 = Enable sound on alarm

|-

|Path and file name of sound file for Low Temperature alarm

|-

*1 = Enable sound on alarm

|-

|Path and file name of sound file for High Temperature alarm

|-

*1 = Enable sound on alarm

|-

|Path and file name for sound file to play for Low Pressure Alarm

|-

*1 = Enable sound on alarm

|-

|Path and file name for the sound file used for the High Pressure Alarm

|-

*1 = Enable sound on alarm

|-

|Path and file name for the sound file used for the High Rain Today Alarm

|-

*1 = Enable sound on alarm

|-

|Path and file name for the sound file used for the High Rain Rate Alarm

|-

*1 = Enable sound on alarm

|-

|Path and file name for the sound file used for the High Gust Alarm

|-

*1 = Enable sound on alarm

|-

|Path and file name for the sound file used for the High Wind Alarm

|-

*1 = Enable sound on alarm

|-

|Path and file name for the sound file used for the Sensor Contact lost Alarm

|-

*1 = Enable sound on alarm

|-

|Path and file name for the sound file used for the Temperature Change Alarm

|-

*1 = Enable sound on alarm

|-

|Path and file name for the sound file used for the Pressure Change Alarm

|}

 

 

{| class="wikitable" border="1"

|-

|style="background:lightgray;"|[Wunderground]

|style="background:lightgray;"|Section Name - Parameters for your [http://www.wunderground.com/ Weather Underground] site

|-

|ID=

*0 = Disabled

*1 = Enabled (default)

|-

|-

|SendSoilTemp1=0

|}

 

Set in the Internet Configuration Screen sites/Options tab

{| class="wikitable" border="1"

|}

 

{| class="wikitable" border="1"

|-

|}

 

Set in the Internet Configuration Screen sites/Options tab

{| class="wikitable" border="1"

|}

 

{| class="wikitable" border="1"

|-

|-

|Interval=15

|-

|SendUV=0

|}

 

{| class="wikitable" border="1"

|-

|-

|Interval=15

|-

|SendUV=0

|}

 

{| class="wikitable" border="1"

|-

|-

|style="background:lightgray;"|[xAP]

|-

|Enabled=0

|}

 

 

{| class="wikitable" border="1"

|-

!style="width:150px" | Parameter Line Entry

!style="width:600px" | Function

|-

|style="background:lightgray;"|[NOAA]

|If set, when Cumulus does the first FTP upload after the daily reset, it will also upload the latest auto-created monthly and yearly NOAA-style reports. Note that you must already have regular (non-realtime) FTP configured.

|-

|-

|Defines the format of the filename used for the yearly reports, using date formatting characters (see [[Webtags#Time.2FDate_.27format.27_Parameter]]). Note that any characters which are not date formatting characters should be in double quotes.

|-

|style="background:lightgray;"| These 'climatic normal' values are set from the NOAA Setup dialog in Cumulus, but could be set up by processing information in a spreadsheet

|-

|-

|}

 

{| class="wikitable" border="1"

|-

!style="width:150px" | Parameter Line Entry

!style="width:600px" | Function

|-

|-

|-

|-

|-

|-

|-

|-

|-

|-

|}